Hardware Specifications

MCU

nRF52840

RAM

-

Flash

-

Display

TFT LCD (0.96)

Button Count

-

Has LEDs

true

Weight

-

Dimensions

-

LoRa Specifications

LoRa Chip

SX1262

Frequency Band

863-870 MHz / 902-928 MHz MHz

Max. TX Power

22 dBm

Antenna Type

-

Connectivity

WiFi

false

Bluetooth

true

GPS

true

Power

USB Type

USB-C

Battery Connector

-

Solar Support

false

Power Consumption (Idle)

-

Power Consumption (TX)

-

Firmware Support

meshcore-dev/MeshCore Official

Room Server v1.17.1 06.06.2026 Release

Release notes: https://blog.meshcore.io/2026/08/14/release-1-17-1

Repeater v1.17.1 06.06.2026 Release

Release notes: https://blog.meshcore.io/2026/08/14/release-1-17-1

BLE Companion v1.17.1 06.06.2026 Release

Release notes: https://blog.meshcore.io/2026/08/14/release-1-17-1

USB Companion v1.17.1 06.06.2026 Release

Release notes: https://blog.meshcore.io/2026/08/14/release-1-17-1

mattzzw/MeshCore-Evo Community

Repeater v1.15.0-evo_0.1.21 14.05.2026 Release

⚠️ Check that radio.rxgain(on) and flood.advert.base (0.308) are set correctly after flashing! ⚠️

This build is based on official MeshCore 1.15.0 dev branch (as of 25-May-2026 and additionally includes the following unmerged upstream PRs/changes:

PR2553: Limit flood advert packet forwarding --> set flood.advert.base 0...1 (0: no flood adv. forwarding, 0.308: default, 1: all flood adv. forwarding)
PR1810: Allow direct message paths when denyf * is set
:new: PR1727: Use hardware channel activity detection for checking interference --> Use set int.thresh 1 to activate hw based channel activity detection.
:new: PR2377: Disable NRF52 undervoltage bootlock feature

Additional changes:

Flood adverts are disabled (flood.advert.interval set to 0) by default
:new: modified PR1810 to not block flood adverts but only PAYLOADTYPEGRPTXT and PAYLOADTYPEGRPDATA so that some limited flood advert distribution can be managed via PR2553 to support e.g. observer maps.

Changelog:

Based on dev v1.15.0 as of 25-May-2026

Full Changelog: https://github.com/mattzzw/MeshCore-Evo/compare/v1.15.0-evo0.1.20...v1.15.0-evo0.1.21

IoTThinks/EasySkyMesh Community

BLE Companion PowerSaving17.1 29.06.2026 Release

Built for long off-road adventures and harsh winter conditions

Based on MeshCore 1.17.1 mainline.
Developed by IoTThinks and tested by our supportive MeshCore friends.
Contribution to MeshCore: By IoTThinks%20is%3Apr%20author%3A%40IoTThinks).
Source code: https://github.com/IoTThinks/MeshCore/tree/PowerSaving-v17
With contributions from Dom4n and MeshCore friends

Notices:

16 Sep 2026: PowerSaving 17.1.5
Disabled automatic light sleep for USB Companion on ESP32 for better serial connectivity.
15 Sep 2026: PowerSaving 17.1.4

Imported a fix for RAK 3401 battery variant from MeshCore dev. If there is no GPS module, 5V power to the LoRa 1W will be floating and unable to provide maximum TX power as expected. Thanks Mr. Martenumberto for your discovery and persistence.
Added BSEC for BME680 on RAK 3401

13 Sep 2026: PowerSaving 17.1.3
(Repeater) RXPSv2: Better power consumption for "set radio.rxps balanced". You can now use "set radio.rxps max". All CLIs are at RXPS CLIs

(Companion) RXPSv2 is enabled by default with powersaving on.

(Repeater) Added support of button press for ESP32 repeaters with powersaving on

(Repeater) Fixed crash if doing "gps" on ESP32 repeaters without GPS module

(Companion) Moved uptime to below battery icon. Shifted dots left.

(Repeaters and sensors) Added "If GPS on after powersaving on", telemetry request will trigger GPS update"

(Sensors) Added MCU temperature

(Sensor) Added PowerSaving for sensor firmware

Added Tracker v2 and T-Deck

Added heltec
trackerv2companionradiousbfemoff and heltectrackerv2companionradiousb_femon

Added board MKE-S3 (Vietnam)

10 Sep 2026: In case you can not see the "uptime" clearly in companions, please upgrade to PowerSaving 17.1.3 05 Sep 2026: You are advised to reboot repeaters / room servers after on/off or changing RXPS settings. Thanks Mr. Gordon for extensive testing.
Custom Development and Partnership
If you want custom development for your projects, Contact Us Looking for Partnership? Discuss Partnership
Support PowerSaving?
Support the development via ![Sponsor](https://www.paypal.com/ncp/payment/6FGWJJVC572VL) or ![Sponsor](https://github.com/sponsors/IoTThinks). Buy boards with a coupon and help support ongoing development.
Instruction:

Flash Custom Firmware as in INSTRUCTION. 👈

Scroll down to bottom to download uf2 / upgrade.bin to upgrade or freshInstall-merged.bin for new devices. 👈

Heltec v4 bin files is for both Heltec v4.2 and v4.3. Heltec v4.3 bin files is for Heltec v4.3 only

Heltec v4.3 and T096 have two options FEM RXgain on and FEM Rxgain off.

If for board build or support, please ask us at GITHUB or Discord

Quick Usage

Repeaters / Room servers
All PowerSaving features are disabled by default and persisted across reboots. PowerSaving: powersaving on, powersaving off and powersaving GPS PowerSaving: powersaving on then gps on and gps. RX PowerSaving: set radio.rxps balanced and get radio.rxps. Repeaters with RXPS enabled are less affected by noises from cell towers. It may due to LoRa RX only wakes up periodically. Added Battery voltage and PowerSaving status to repeater OLED Set dark theme for Heltec T096. For Heltec v4.3, 4.3R8, T096 and Tracker v2, you may set FEM off to save 10mA: set radio.fem.rxgain off

BLE / USB Companions

All PowerSaving features are enabled by default. GPS PowerSaving is enabled when you enable Position in MeshCore app. Added uptime for all companions. Set dark theme for Heltec T096.

For Heltec v4.3, 4.3R8, T096 and Tracker v2, you may use femoff version to save 10mA.

Complete Guides in Wiki

Check the PowerSaving Wiki for more details:

All the features
All CLI commands
How it works
Test results

Enjoy MeshCore with PowerSaving. 👍

Repeater PowerSaving17.1 29.06.2026 Release

Built for long off-road adventures and harsh winter conditions

Based on MeshCore 1.17.1 mainline.
Developed by IoTThinks and tested by our supportive MeshCore friends.
Contribution to MeshCore: By IoTThinks%20is%3Apr%20author%3A%40IoTThinks).
Source code: https://github.com/IoTThinks/MeshCore/tree/PowerSaving-v17
With contributions from Dom4n and MeshCore friends

Notices:

16 Sep 2026: PowerSaving 17.1.5
Disabled automatic light sleep for USB Companion on ESP32 for better serial connectivity.
15 Sep 2026: PowerSaving 17.1.4

Imported a fix for RAK 3401 battery variant from MeshCore dev. If there is no GPS module, 5V power to the LoRa 1W will be floating and unable to provide maximum TX power as expected. Thanks Mr. Martenumberto for your discovery and persistence.
Added BSEC for BME680 on RAK 3401

13 Sep 2026: PowerSaving 17.1.3
(Repeater) RXPSv2: Better power consumption for "set radio.rxps balanced". You can now use "set radio.rxps max". All CLIs are at RXPS CLIs

(Companion) RXPSv2 is enabled by default with powersaving on.

(Repeater) Added support of button press for ESP32 repeaters with powersaving on

(Repeater) Fixed crash if doing "gps" on ESP32 repeaters without GPS module

(Companion) Moved uptime to below battery icon. Shifted dots left.

(Repeaters and sensors) Added "If GPS on after powersaving on", telemetry request will trigger GPS update"

(Sensors) Added MCU temperature

(Sensor) Added PowerSaving for sensor firmware

Added Tracker v2 and T-Deck

Added heltec
trackerv2companionradiousbfemoff and heltectrackerv2companionradiousb_femon

Added board MKE-S3 (Vietnam)

10 Sep 2026: In case you can not see the "uptime" clearly in companions, please upgrade to PowerSaving 17.1.3 05 Sep 2026: You are advised to reboot repeaters / room servers after on/off or changing RXPS settings. Thanks Mr. Gordon for extensive testing.
Custom Development and Partnership
If you want custom development for your projects, Contact Us Looking for Partnership? Discuss Partnership
Support PowerSaving?
Support the development via ![Sponsor](https://www.paypal.com/ncp/payment/6FGWJJVC572VL) or ![Sponsor](https://github.com/sponsors/IoTThinks). Buy boards with a coupon and help support ongoing development.
Instruction:

Flash Custom Firmware as in INSTRUCTION. 👈

Scroll down to bottom to download uf2 / upgrade.bin to upgrade or freshInstall-merged.bin for new devices. 👈

Heltec v4 bin files is for both Heltec v4.2 and v4.3. Heltec v4.3 bin files is for Heltec v4.3 only

Heltec v4.3 and T096 have two options FEM RXgain on and FEM Rxgain off.

If for board build or support, please ask us at GITHUB or Discord

Quick Usage

Repeaters / Room servers
All PowerSaving features are disabled by default and persisted across reboots. PowerSaving: powersaving on, powersaving off and powersaving GPS PowerSaving: powersaving on then gps on and gps. RX PowerSaving: set radio.rxps balanced and get radio.rxps. Repeaters with RXPS enabled are less affected by noises from cell towers. It may due to LoRa RX only wakes up periodically. Added Battery voltage and PowerSaving status to repeater OLED Set dark theme for Heltec T096. For Heltec v4.3, 4.3R8, T096 and Tracker v2, you may set FEM off to save 10mA: set radio.fem.rxgain off

BLE / USB Companions

All PowerSaving features are enabled by default. GPS PowerSaving is enabled when you enable Position in MeshCore app. Added uptime for all companions. Set dark theme for Heltec T096.

For Heltec v4.3, 4.3R8, T096 and Tracker v2, you may use femoff version to save 10mA.

Complete Guides in Wiki

Check the PowerSaving Wiki for more details:

All the features
All CLI commands
How it works
Test results

Enjoy MeshCore with PowerSaving. 👍

Automatic sync from different repositories