Heltec WSL3

⚠️ Check that radio.rxgain(on) and flood.advert.base (0.308) are set correctly after flashing! ⚠️

This build is based on official MeshCore 1.15.0 dev branch (as of 25-May-2026 and additionally includes the following unmerged upstream PRs/changes:

• PR2553: Limit flood advert packet forwarding --> set flood.advert.base 0...1 (0: no flood adv. forwarding, 0.308: default, 1: all flood adv. forwarding)
• PR1810: Allow direct message paths when denyf * is set
• :new: PR1727: Use hardware channel activity detection for checking interference --> Use set int.thresh 1 to activate hw based channel activity detection.
• :new: PR2377: Disable NRF52 undervoltage bootlock feature

Additional changes:

• Flood adverts are disabled (flood.advert.interval set to 0) by default
• :new: modified PR1810 to not block flood adverts but only PAYLOADTYPEGRPTXT and PAYLOADTYPEGRPDATA so that some limited flood advert distribution can be managed via PR2553 to support e.g. observer maps.

Changelog:

• Based on dev v1.15.0 as of 25-May-2026

Full Changelog: https://github.com/mattzzw/MeshCore-Evo/compare/v1.15.0-evo0.1.20...v1.15.0-evo0.1.21

Built for long off-road adventures and harsh winter conditions

• Based on MeshCore 1.17.1 mainline.
• Developed by IoTThinks and tested by our supportive MeshCore friends.
• Contribution to MeshCore: By IoTThinks%20is%3Apr%20author%3A%40IoTThinks).
• Source code: https://github.com/IoTThinks/MeshCore/tree/PowerSaving-v17
• With contributions from Dom4n and MeshCore friends

Notices:

10 Sep 2026: In case you can not see the "uptime" clearly in companions, please ask us to build the fixed firmware for you in Instruction section. 05 Sep 2026: You are advised to reboot repeaters / room servers after on/off or changing RXPS settings to apply the setting the fullest.. Thanks Mr. Gordon for extensive testing.

Custom Development and Partnership

If you want custom development for your projects, Contact Us Looking for Partnership? Discuss Partnership

Contribute to PowerSaving?

Support us via  or .

Instruction:

• Flash Custom Firmware as in INSTRUCTION.
• Scroll down to bottom to download uf2 / upgrade.bin to upgrade or freshInstall-merged.bin for new devices.
• Heltec v4 bin files is for both Heltec v4.2 and v4.3. Heltec v4.3 bin files is for Heltec v4.3 only
• Heltec v4.3 and T096 have two options FEM RXgain on and FEM Rxgain off.
• If for board build or support, please ask us at GITHUB or Discord

Quick Usage

Repeaters / Room servers

All PowerSaving features are disabled by default and persisted across reboots. PowerSaving: powersaving on, powersaving off and powersaving GPS PowerSaving: powersaving on then gps on and gps. RX PowerSaving: set radio.rxps balanced and get radio.rxps. Repeaters with RXPS enabled are less affected by noises from cell towers. It may due to LoRa RX only wakes up periodically. You are strongly advised to reboot repeaters / room servers after on/off or changing RXPS settings. Added Battery voltage and PowerSaving status to repeater OLED Set dark theme for Heltec T096.

BLE / USB Companions

All PowerSaving features are enabled by default. GPS PowerSaving is enabled when you enable Position in MeshCore app. Added uptime for all companions.

• Set dark theme for Heltec T096.

Complete Guides in Wiki

Check the PowerSaving Wiki for more details:

• All the features
• All CLI commands
• How it works
• Test results

Enjoy MeshCore with PowerSaving. 👍

Built for long off-road adventures and harsh winter conditions

• Based on MeshCore 1.17.1 mainline.
• Developed by IoTThinks and tested by our supportive MeshCore friends.
• Contribution to MeshCore: By IoTThinks%20is%3Apr%20author%3A%40IoTThinks).
• Source code: https://github.com/IoTThinks/MeshCore/tree/PowerSaving-v17
• With contributions from Dom4n and MeshCore friends

Notices:

10 Sep 2026: In case you can not see the "uptime" clearly in companions, please ask us to build the fixed firmware for you in Instruction section. 05 Sep 2026: You are advised to reboot repeaters / room servers after on/off or changing RXPS settings to apply the setting the fullest.. Thanks Mr. Gordon for extensive testing.

Custom Development and Partnership

If you want custom development for your projects, Contact Us Looking for Partnership? Discuss Partnership

Contribute to PowerSaving?

Support us via  or .

Instruction:

• Flash Custom Firmware as in INSTRUCTION.
• Scroll down to bottom to download uf2 / upgrade.bin to upgrade or freshInstall-merged.bin for new devices.
• Heltec v4 bin files is for both Heltec v4.2 and v4.3. Heltec v4.3 bin files is for Heltec v4.3 only
• Heltec v4.3 and T096 have two options FEM RXgain on and FEM Rxgain off.
• If for board build or support, please ask us at GITHUB or Discord

Quick Usage

Repeaters / Room servers

All PowerSaving features are disabled by default and persisted across reboots. PowerSaving: powersaving on, powersaving off and powersaving GPS PowerSaving: powersaving on then gps on and gps. RX PowerSaving: set radio.rxps balanced and get radio.rxps. Repeaters with RXPS enabled are less affected by noises from cell towers. It may due to LoRa RX only wakes up periodically. You are strongly advised to reboot repeaters / room servers after on/off or changing RXPS settings. Added Battery voltage and PowerSaving status to repeater OLED Set dark theme for Heltec T096.

BLE / USB Companions

All PowerSaving features are enabled by default. GPS PowerSaving is enabled when you enable Position in MeshCore app. Added uptime for all companions.

• Set dark theme for Heltec T096.

Complete Guides in Wiki

Check the PowerSaving Wiki for more details:

• All the features
• All CLI commands
• How it works
• Test results

Enjoy MeshCore with PowerSaving. 👍

Built for long off-road adventures and harsh winter conditions

• Based on MeshCore 1.17.1 mainline.
• Developed by IoTThinks and tested by our supportive MeshCore friends.
• Contribution to MeshCore: By IoTThinks%20is%3Apr%20author%3A%40IoTThinks).
• Source code: https://github.com/IoTThinks/MeshCore/tree/PowerSaving-v17
• With contributions from Dom4n and MeshCore friends

Notices:

10 Sep 2026: In case you can not see the "uptime" clearly in companions, please ask us to build the fixed firmware for you in Instruction section. 05 Sep 2026: You are advised to reboot repeaters / room servers after on/off or changing RXPS settings to apply the setting the fullest.. Thanks Mr. Gordon for extensive testing.

Custom Development and Partnership

If you want custom development for your projects, Contact Us Looking for Partnership? Discuss Partnership

Contribute to PowerSaving?

Support us via  or .

Instruction:

• Flash Custom Firmware as in INSTRUCTION.
• Scroll down to bottom to download uf2 / upgrade.bin to upgrade or freshInstall-merged.bin for new devices.
• Heltec v4 bin files is for both Heltec v4.2 and v4.3. Heltec v4.3 bin files is for Heltec v4.3 only
• Heltec v4.3 and T096 have two options FEM RXgain on and FEM Rxgain off.
• If for board build or support, please ask us at GITHUB or Discord

Quick Usage

Repeaters / Room servers

All PowerSaving features are disabled by default and persisted across reboots. PowerSaving: powersaving on, powersaving off and powersaving GPS PowerSaving: powersaving on then gps on and gps. RX PowerSaving: set radio.rxps balanced and get radio.rxps. Repeaters with RXPS enabled are less affected by noises from cell towers. It may due to LoRa RX only wakes up periodically. You are strongly advised to reboot repeaters / room servers after on/off or changing RXPS settings. Added Battery voltage and PowerSaving status to repeater OLED Set dark theme for Heltec T096.

BLE / USB Companions

All PowerSaving features are enabled by default. GPS PowerSaving is enabled when you enable Position in MeshCore app. Added uptime for all companions.

• Set dark theme for Heltec T096.

Complete Guides in Wiki

Check the PowerSaving Wiki for more details:

• All the features
• All CLI commands
• How it works
• Test results

Enjoy MeshCore with PowerSaving. 👍

Full Changelog: https://github.com/MichTronics/MeshCoreNG/compare/bridge-tcp-v1.0.5...repeater-v1.0.1

Full Changelog: https://github.com/MichTronics/MeshCoreNG/compare/bridge-tcp-v1.0.5...companion-v1.0.1

Full Changelog: https://github.com/MichTronics/MeshCoreNG/compare/bridge-tcp-v1.0.5...companion-v1.0.1

Full Changelog: https://github.com/MichTronics/MeshCoreNG/compare/bridge-tcp-v1.0.5...room-server-v1.0.1